Outboard Motor Repair Outboard Motor Repair  

Outboard Motors

Power Heads

Lower Units

Props

Repair Manuals

Controls, Steering

Trim/Tilt

Power Tilt/Trim

Parts

Outboard Motor Repair


Chrysler
Evinrude
Force
Honda
Johnson
Mariner
Mercury
Minn Kota
Nissan
OMC
Suzuki
Yamaha
2 Cycle Outboard Motors
2 Stroke Outboards
4 Cycle Outboards
4 Stroke Outboards
Aftermarket Outboard Parts
Boat Wont Plane
Bolts
Brackets
Carburetors
Cavitation
Choke
Coils
Compression
Condensors
Controls
Cooling
Cowling
Crankshafts
Cylinders
Diagrams
EFI
Electrical
Engine Cleaner
Engine Smoke
Exhaust
FICHT
Fins
Flywheel
Fouling
Fuel Pumps
Fuel Systems
Fuel Tanks
Gaskets
Gauges
Gear Cases
Generators
I/O
Idle
Ignition
Impellers
Inverters
Kill Switch
Leaks
Lower Units
Lubrication
Manuals
Oil
Oil Injection
Oil Mixture
Old Outboards
Outboard Engine Blocks
Outboard Inboard
Outboard Maintenance
Outboard Motor Prices
Outboard Propellers
Paint
Parts
Pistons
Power Loss
Power Packs
Powerheads
Primer Bulb
RPM
Repair Tools
Reverse
Running Lean
Running Rich
Runs Hot
Sea Drives
Sealants
Shafts
Shifter
Skegs
Spark Plugs
Specs
Spring Maintenance
Starter Motors
Starting Problems
Stators
Steering
Synthetic Oil
Tachometers
Tillers
Tilt Trim
Timing
Trim Tabs
Twin Outboards
V6
Voltmeter
Water Pumps
Winterization
Wiring
Year

Repowering old tri-hull

AV8R I'd like to repower my old Signa tri-hull. It currently has an inline 6 cyl 165 Mercruiser. How tough will it be to go to a V-6 or V-8? Should I just go to a fuel injection system? If so, where can I get one that is marine rated? 2001-08-04
12Footer AV8R, you asked, and this is just my opinion...Stick with the mercruiser 6, or even look into the volvo. The reason I would stay with the smaller engine is fuel economy.
The bigger block will give you the capabilty of runnin a huge prop, and give breakneck speeds,but at a very high cost. Expect to pay twice as much to go the same distance....Even if if IS a shorted trip.
2001-08-04
Liljoe Go out and look for a 250 block out of a chevy truck in the junk yard from the 70's. Make sure the mounting holes are the same and just rebuild the block. The heads from the old engine will need redone to run unleaded and you will need to get a cam that will give you good torque at low rpms. We have rebuilt the original motor twice and the improvement we ended up with when we started with a fresh block was what we were looking for. By changing to a V you will have to change your outdrive and wouldn't it be cheaper buying another boat? Ours is in a 1970 signa tri-haul. With nine adults in the boat for the day we have no problems pulling three tubes and 18 gallons of gas lasting all day. 2001-08-05

If you would like to post your own question for the experts just click on
the Boating Forums tab at the top of the page or click here!

Disclaimer: iboats.com provides this content for the education and benefit of all boating enthusiasts.
We cannot, however, take responsibility for individual postings, nor can we verify the accuracy of any posting.
Please use any information provided from individuals with great care and read any applicable manuals or safety instructions.
Also, if you determine that a posting is inaccurate or offensive in any manner, please use the Contact Us email form found below.

If you would like to post your own question for the experts just click on the Boating Forums tab at the top of the page!


Outboard Motors

Power Heads

Lower Units

Props

Repair Manuals

Controls, Steering

Trim/Tilt

Power Tilt/Trim

Parts

Outboard Repairs | Boats | Outboard Motors | Boat Dealers
Boat Covers | Boat Propellers | Boat Repair | Marine Engines | Outboard Forum Directory
Terms of Use | Privacy Practices | Legal Notices

1-800-869-1686 (Toll Free)
001-801-571-0071 (International Calls)
Copyright © 1999-2009 iboats, inc. All rights reserved.