Outboard Motor Repair Outboard Motor Repair  

Outboard Motors

Power Heads

Lower Units

Props

Repair Manuals

Controls, Steering

Trim/Tilt

Power Tilt/Trim

Parts

Outboard Motor Repair


Chrysler
Evinrude
Force
Honda
Johnson
Mariner
Mercury
Minn Kota
Nissan
OMC
Suzuki
Yamaha
2 Cycle Outboard Motors
2 Stroke Outboards
4 Cycle Outboards
4 Stroke Outboards
Aftermarket Outboard Parts
Boat Wont Plane
Bolts
Brackets
Carburetors
Cavitation
Choke
Coils
Compression
Condensors
Controls
Cooling
Cowling
Crankshafts
Cylinders
Diagrams
EFI
Electrical
Engine Cleaner
Engine Smoke
Exhaust
FICHT
Fins
Flywheel
Fouling
Fuel Pumps
Fuel Systems
Fuel Tanks
Gaskets
Gauges
Gear Cases
Generators
I/O
Idle
Ignition
Impellers
Inverters
Kill Switch
Leaks
Lower Units
Lubrication
Manuals
Oil
Oil Injection
Oil Mixture
Old Outboards
Outboard Engine Blocks
Outboard Inboard
Outboard Maintenance
Outboard Motor Prices
Outboard Propellers
Paint
Parts
Pistons
Power Loss
Power Packs
Powerheads
Primer Bulb
RPM
Repair Tools
Reverse
Running Lean
Running Rich
Runs Hot
Sea Drives
Sealants
Shafts
Shifter
Skegs
Spark Plugs
Specs
Spring Maintenance
Starter Motors
Starting Problems
Stators
Steering
Synthetic Oil
Tachometers
Tillers
Tilt Trim
Timing
Trim Tabs
Twin Outboards
V6
Voltmeter
Water Pumps
Winterization
Wiring
Year

1973 chrysler outboard timing belt

rip49096 i have a 120 horse chrysler out board and the timing belt is broke how do i put a new one on i have the fly wheel off now. 2002-06-21
Terry H rip...it would be good if you had a manual but I will try to help you, all from memory.
Loosen the bolt holding the distributor tension and swing the dist. into the block. Place the belt over the pully and in place so the flywheel will not bind it...once the flywheel is on and torqued properly turn flywheel until it is at tdc on timing mark for cyl #1. There should be a mark on the distributor pulley that will coincide with with the flywheel...engage the belt with the scribe mark on the pully lined with the flywheel and tighten the distributor bolt. About 1/8" movement in belt max. Set the timing and you are set to go. If you need timing info you will need to get the year of motor for me so I can look it up. Good luck
2002-06-22

If you would like to post your own question for the experts just click on
the Boating Forums tab at the top of the page or click here!

Disclaimer: iboats.com provides this content for the education and benefit of all boating enthusiasts.
We cannot, however, take responsibility for individual postings, nor can we verify the accuracy of any posting.
Please use any information provided from individuals with great care and read any applicable manuals or safety instructions.
Also, if you determine that a posting is inaccurate or offensive in any manner, please use the Contact Us email form found below.

If you would like to post your own question for the experts just click on the Boating Forums tab at the top of the page!


Outboard Motors

Power Heads

Lower Units

Props

Repair Manuals

Controls, Steering

Trim/Tilt

Power Tilt/Trim

Parts

Outboard Repairs | Boats | Outboard Motors | Boat Dealers
Boat Covers | Boat Propellers | Boat Repair | Marine Engines | Outboard Forum Directory
Terms of Use | Privacy Practices | Legal Notices

1-800-869-1686 (Toll Free)
001-801-571-0071 (International Calls)
Copyright © 1999-2009 iboats, inc. All rights reserved.